Header image

MINIWOLF 70 LED: the electronic transformer for 12 Vac LED bulbs

Posted by admingb in Electronic Transformers | LED Driver | News - (Comments Off)

MINIWOLF 70 LED 1÷70 W
MINIWOLF 70 LED in an independent dimmable (IGBT) electronic transformer for 12 Vac LED bulbs and 12 V halogen lamps. Thanks to its 1 W minimum load and 230-240 V supply voltage it is suitable for universal use.

 MINIWOLF 70 LED Dimmable – MINIWOLF 70 LED not Dimmable

,

MP 55 HC BI

Posted by admingb in LED Driver | News - (Comments Off)

MP 55 HC BI
Multi-current electronic power supply unit for power LED’s and LED modules
Another novelty that will be presented in the new Frankfurt Show is the MP 55 HC BI. It is a driver that is capable to drive LED’s up to a 2100mA current, designed for high-intensity LED lighting, were no regulation is required, but where it is essential to have high power (with an active PFC), flexibility in the selection of the output current and lower costs than a dimmable solution. MP 55 HC BI is fitted with a dip-switch to select the output current (1050mA to 2100mA) and a secondary 12 V output for an active heat dissipation system (max. 100 mA, usable through a separate accessory cable).

 pagina in .PDF

, ,

MP 50 K3

Posted by admingb in LED Driver | News - (Comments Off)

MP 50 K3
Multi-current and multi-tension electronic power supply unit for power LED’s and LED modules
One of the new products that will be presented in the new Frankfurt Show is the MP 50 K3. It is a high-performance and low-cost driver, conceived and designed for LED lighting solutions where light does not NOT require dimming, but where it is essential to have high power (with an active PFC), flexibility in the selection of the output current and lower costs than a dimmable solution. MP 50 K3 is fitted with a dip-switch to select the output current (350mA to 1050mA) and a secondary 12 V output for an active heat dissipation system (max. 50 mA).

 pagina in .PDF

, ,

BMU DMX INTERFACE, DMX – PWM signal converter.

Posted by admingb in ACCESSORIES | LED Driver | News - (Comments Off)

BMU DMX INTERFACE can convert a signal with DMX  protocol into three signals PWM signal, selecting the DMX address through three selectors on the upper side of the interface.
Through 3 pwm outputs it is possible to connect up to 30 drivers of the Jolly series through the sync cable, one for each RGB channel. It is possible to use one RGB multichannel sync cable to connect up to 10 drivers of the VSTR RGB, WU RGB or LV RGB IR series.
The interface is protected against input overvoltages from mains, short circuit and open circuit and thermal and overload temperature. 
  .PDF page

, ,

You are already part of it with your heart

Posted by admingb in News - (1 Comments)

“Dear Friends, this is the party of light in every respect: the light of ethics, of seriousness and of concreteness.
All together we will succeed in changing the country and in going back to the road of seriousness.
Italy, if united, will be able to give a future to our young people and to find again that pride that flows inside our blood of free, pragmatic and strong men and women.

GIVE ME A HAND! TAKE PART IN OUR PROJECT AND SUBSCRIBE TO  OUR MOVEMENT“.

Gianfranco Librandi

, ,

MAXI JOLLY BILEVEL

Posted by admingb in LED Driver | News - (Comments Off)

Direct current dimmable electronic drivers multivoltage-multicurrent for power LED and LED modules.

Multicurrent LED driver suitable for street lighting as it allows the reduction of the power using a simple 0-230 V control signal.
It’s possible to fix the reduction level with a simple programming or by connecting a resistor to the LEVEL terminal block.

.PDF page

,

STMP/U IP54

Posted by admingb in LED Driver | News - (Comments Off)

IP54 resin-bonded direct current electronic drivers for power LED and LED modules

Driver with IP54 case, suitable for installation in humid environments or with water spray (ex. bathrooms).
Supplied with input and output cables on the same side.
Protections against overheating and short circuits, against mains voltage spikes and against overloads.

 .PDF page

,

DC WOLF MP, multi power with Active PFC

Posted by admingb in LED Driver | News - (Comments Off)

DC WOLF MP, multi power with Active PFC
This driver has been conceived and designed for LED down-lighting installations where no regulation is required but where it is essential to have a lighting device with 0,95 active PFC. It is fitted with a dip switch for selecting currents varying from 350, 500, 550, 700 and 750mA and output voltages of 12.24 and 28V. The maximum power varies from 17 to 32W.

code: 122252

.PDF page .PDF instruction sheet code 419840571

,

DC MAXI JOLLY HC BI

Posted by admingb in LED Driver | News - (Comments Off)

DC MAXI JOLLY HC BI, currents selectable from 1 to 2.1A and dimmable
It is the latest in the JOLLY family, with a maximum power of 55W. This driver has been designed to feed the power LEDs currently available on the market, with feed currents up to 2.1 A.
DC MAXI JOLLY HC is presented in two versions, one which can be dimmed with 1…10V and PUSH system and one with DALI system. Both versions are fitted with an auxiliary 12V 50mA output for a cooling fan and an analogue input for connecting a thermal sensor. This feeder can select outgoing current via a dipswitch with values of 1.05, 1.2 , 1.4 ,1.6 ,1.8 and 2.1 A and powers varying from 50 to 55W ; moreover, thanks to the compact dimensions the same as electronic feeders for HID lamps, it can be installed in already existing lighting units.

code: 122415

.PDF page .PDF instruction sheet code 419840582

 

, ,

Roberto Formigoni visit TCI

Posted by admingb in News - (Comments Off)

Roberto Formigoni, President of the Lombardy Region, visit our Company.

In the news of TvVarese

Interview Gianfranco Librandi